Reference: W.H_FW-09.01-L400
Bridge height: 70 mm Bridge width: 115 mm EPDM tape Aluminium
Reference: W.H_FW UCH-22
Material: stainless steel Thickness [mm] 4 Width [mm] 32 Length [mm] 82 Hole diameter [mm] 11 Additional information: Adjustment opening 40x11 mm.
Reference: M.H_NAKR KW M8
Technical data: diameter - M8 material - A2 stainless steel (1.4301) Standard - DIN 557
Banner
Polityka bezpieczeństwa
Zasady zwrotu
In the case of installation on large roof surfaces - if the roof is covered with trapezoidal sheet, a 2200mm bridge can be used. It is a bridge of similar construction at 300mm and 400mm, so it can be easily connected with our other bridges. The length of the bridge can be adjusted and adapted to different needs. Since it is fully made of aluminum it can be trimmed quickly. The bridge is constructed in such a way that it can be mounted directly on the roof with screws. This is made possible by the use of EPDM tape, which insulates the bridge from the roof, protecting it from leaks at the mounting points. The height of the bridge is optimized so that there is free air flow between the panels and the roof.
For proper installation of the panels end and middle clamps are needed. The clamps are fastened on sliding grooves with a ball or square nut. One of these elements slides into the upper part of the bridge and, after positioning in a satisfactory place, we connect the given clamp with a screw. End clamps are used to fix the outer panels and the middle clamp is to separate the panels from each other.
Reference: M.H_WKRET SM M6X25
Size: 6.0x25 + 16mm / A2 EPDM washer
Reference: W.H_FW-09.01-L300
Bridge length: 300 mm Bridge height: 70 mm Bridge width: 114 mm EPDM tape
Reference: W.H_FW-25.01-L330
Bridge length: 330 mm Bridge height: 100 mm Bridge width: 119 mm EPDM tape Aluminium
Reference: M.H_NAKR KW M8
Technical data: diameter - M8 material - A2 stainless steel (1.4301) Standard - DIN 557
Reference: W.H_FW-05.01 30MM CZ
Material: Aluminum For module with a frame thickness [mm] 30 Hole diameter [mm] 9 Serration in the place where the module is attached Color: black
Reference: W.H_FW-01.01 CZ
Material: Aluminum Height [mm] 25 Width [mm] 20 Length [mm] 50 Hole diameter [mm] 9 Serration in the place where the module is attached Color: black
Reference: M.H_NAKR PROF M8
<p>T-Slot Nut with M8 ball studs - full name "T-Slot Nut with M8 ball studs". This is a small but very important element that helps in the construction of the structure and installation of solar panels. Thanks to the use of a ball on one end of the gully, it can be set in the desired place without fear of displacement during tightening. A substitute...
Reference: W.H_FW-05.01 30MM CZ
Material: Aluminum For module with a frame thickness [mm] 30 Hole diameter [mm] 9 Serration in the place where the module is attached Color: black
Reference: W.H_FW-04.02
Mounting profile connector Length: 120 mm Width: 45 mm Height: 25 mm Aluminum
Reference: PV-TRI-SV.TSM-DE09.08-395W-B
Brand: TrinaSolar
Reference: M.H_NAKR KW M8
Technical data: diameter - M8 material - A2 stainless steel (1.4301) Standard - DIN 557
Reference: W.H_FW-KDP-H15ST.01L
Horizontal aluminum mounting triangle with an angle of 15° for mounting solar panels on flat or low-slope roofs. Angle: 40x40 mm Angle thickness: 3 mm
Reference: W.H_FW-01.01 CZ
Material: Aluminum Height [mm] 25 Width [mm] 20 Length [mm] 50 Hole diameter [mm] 9 Serration in the place where the module is attached Color: black
Reference: W.H_FW-25.01-L330
Bridge length: 330 mm Bridge height: 100 mm Bridge width: 119 mm EPDM tape Aluminium
Reference: W.H_FW-KPI-0001.00
The mounting bracket is dedicated to the installation of solar modules from 155Wp to 310Wp. The bracket is perfect for pole mounting.
